Support Our Sponsors! Click On Their Banner To Visit Their Site!

Moderators: nmhunter
600 rem bolt in xp 100 Login/Join 

Sold my Striker so a little extra money.Have an original xp 100 221 FB.Thinking on doing a Remage.If I go to-Im thinking-6x47 lapua,could I use a bolt out of my 600 or my 660 rem.rifles both 243? Then just put back in rifle when needed? Or would any work need done to bolt?If work would be needed i would try to find another bolt as both rifles are mint. Another thing .I would need another stock for a heavy bbl-been looking on auction sites with no luck.Any one knows who sells them?I dont shoot competition,just targets and groundhogs so a less expensive one or used would be greatly appreciated THANKS for any advise p.s. also have a 350 rem mag rifle-also a 600 Rem.,could I use bolt for a mag caliber with no alterations to bolt?

This message has been edited. Last edited by: sharkyf9,
Posts: 98 | Location: upper east tennessee | Registered: January 24, 2018Reply With QuoteReport This Post

Picture of Gator T/C
posted Hide Post
The bolts should fit fine but the headspace “might” be different depending on which bolt you used from which gun. Magnum bolt would fit fine but again headspace chech but easy to adjust with Remage setup.


Contender 22LR, 17MachII, 17HMR, .223(SSK), 6mm Gator, 6TCU, 6mmJDJ(Van Horn), 25x47(Coyote), 6.5 JDJ(SSK), 7x47(SSK),308 Bellm, .338 SSK Woodswalker (2),358 Bellm, 375Win, 375 JDJ(SSK), 45/70(SSK), 45/70 (VanHorn), 50-70(SSK)
Encore .243, 7mm–08, 300WM(15-1/4"), 50-90(MGM, 14"), 50–110 (MGM), .50ML(16")
XP-100 .223, .223AI, 6mm204Imp, .243AI, 6BR
XP-7 .223,.243,.300Blackout, .300RSAUM
XP-700SA .22LR, .243
XP-700LA .25/06, .270AI, .300WM,.338 Lapua, .510 Whisper
Posts: 1244 | Location: Gainesville, Fl | Registered: January 01, 2005Reply With QuoteReport This Post

posted Hide Post
Why not do a 6x45 and use the existing bolt.
Not a huge difference in performance and you don't take apart your other gun.
Posts: 129 | Location: South LA | Registered: March 09, 2020Reply With QuoteReport This Post

posted Hide Post
6x45 would be good for me.Since I have to rebarrel for the 6mm,may as well get a little more.Sliding a bolt out of the 600 rifles is simple enough.Then slide back in when I shoot them.Luckily,have little over a thousand 6mm bullets,mostly Bergers I got YEARS ago-probably 10 or more.
Posts: 98 | Location: upper east tennessee | Registered: January 24, 2018Reply With QuoteReport This Post


posted Hide Post
I second 6x45
I find mine to be very accurate

Cases were easy to make

Posts: 744 | Location: San Jose CA | Registered: November 12, 2005Reply With QuoteReport This Post
  Powered by Social Strata  

© Specialty Pistols 2003 - 2021 All Rights Reserved.
All Material Contained Here Is Protected And May NOT Be Reproduced,
Copied or Distributed, in any form, Without Written Permission.
"Specialty Pistols", "Specialty Pistols Bulletin Board" and
"Specialty Pistol Gear" are Trademarks of
Accurate Arms & Ammo, LLC.